Page 109: Software Configuration Using 4-/6-channel Audio Function Software Configuration To have 4-/6-channel audio work, you must set appropriate configuration in the C-Media software application. Page 20 Hardware SetupPower SupplyThe mainboard supports ATX power supply for the power system.Before inserting the power supply connectors, always make sure that all components are installed properly to ensure that Settings: 1.4 and 1.1.Boot OS/2 for DRAM > 64MBThis allows you to run the OS/2® operating system with more than 64MBDRAM. If an audio device is detected, the onboard AC’97 controllerwill be enabled; if not, the controller is disabled.
OnBoard Game Port The item specifies I/O port address for the onboard Joystick/Game port. You can usethe arrow keys ( ↑↓ ) to select the item. Half- Duplex mode permits transmission in one direction only at a time. Page 23 Chapter 2Keyboard ConnectorThe mainboard provides a standard PS/2® keyboard mini DIN connector for attaching a PS/2® keyboard.
The openings on the enclosure are for air convection hence protects the equipment from overheating. Settings: Auto and Disabled. If set to Setup,password prompt only occurs when you try to enter Setup. Avoid rebooting while the HDD is working.
The on-line description for the selectedsetup category is displayed on the bottom of the screen.General Help The BIOS setup program provides a General Help screen. The mainboard uses a CPU socket called Socket 478 for easy CPU installation. All Rights Reserved USB Controller :All USB Port USB Legacy Support :Disabled On-Chip IDE :Both Onboard Audio Chip :Enabled AC’97 Audio :Auto AC’97 Modem :Auto Floppy Controller :Enabled Serial Port A Settings: Enabled and Disabled.1st/2nd/3rd Boot DeviceThe items allow you to set the sequence of boot devices where BIOSattempts to load the disk operating system.
It supports three-pin head connector. It has twoHDD connectors IDE1 (Primary) and IDE2 (Secondary). This section will explain how to change your motherboard’s function through the use of jumpers. https://www.msi.com/Motherboard/MS6534.html PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its special components.
A message as below will appear on the screen.AMIBIOS SIMPLE SETUP UTILITY - VERSION 1.41(C)1999 American Megatrends, Inc. You can buy the MSI Z97M ... 128MB RAM Memory for MSI MS-6500 Series MS-6534 (845M) 164pin PC133 SDRAM DIMM 133MHz Black Diamond Check on Amazon 128MB RAM Memory for Microstar (MSI) power cord, if any, must be used in order to comply with the emission limits. Avoid turning the power off while the HDD is working.
ExtSMI# JGS1 Wake On LAN Connector: JWOL1 This connector allows you to connect to a LAN card with Wake On LAN function. http://www.ps2netdrivers.net/manual/msi.ms-6534.micro.atx.mainboard/ When the message below appears on the screen, press
key to enter Setup. A20 refers to the...Page 53Chapter 3 MPS Version Control For OS This field allows you to select which MPS (Multi-Processor Specification) version to be...Page 54: Advanced Chipset Features AWARD® BIOS Setup If you want to configure the system by yourself, select Manaul.
Page 3 EditionAugust 2001Copyright NoticeThe material in this document is the intellectual property of MICROSTAR INTERNATIONAL. Oh no! The difference between IR1 & IR2 is that IR2 is compliant to Intel Front Panel I/O Connectivity Design Guide. Hardware Setup ............2-1 Central Processing Unit: CPU ........... 2-2 Installing the CPU ............... 2-2 Installing the CPU Fan ............
Page 37: Usb Front Panel Connectors: Usb1 & Usb2 Chapter 2 USB Front Panel Connectors: USB1 & USB2 The mainboard provides two Front USB (Universal Serial Bus) pin head- ers that IRQ Resources This item is adjustable only when Resources Controlled By is set to Manual. Page 2 Manual Rev: 1.0Release Date: August 2001FCC-B Radio Frequency Interference StatementThis equipment has been tested and found to comply with the limits for aclass B digital device, pursuant to part The Fail-Safe Defaults are the defaultvalues set by the BIOS vendor for the stable system performance.
To use the function, you need to install the C-Media drivers. All Rights Reserved ******** DRAM...Page 87 AMI® BIOS Setup allowed to precharge. Page 29 Chapter 2Power SwitchConnect to a 2-pin push button switch.Reset SwitchReset switch is used to reboot the system rather than turning the power ON/OFF.
Hardware Setup Hardware Setup This chapter provides you with the information about hardware setup procedures. Page 73 Chapter 3Save & Exit SetupWhen you want to quit the Setup menu, you can select this option to save thechanges and quit. Page 50 AWARD® BIOS SetupAdvanced BIOS FeaturesCMOS Setup Utility - Copyright (C) 1984-2001 Award SoftwareAdvanced BIOS FeaturesAnti-Virus ProtectionCPU L1 & L2 CacheQuick Boot1st Boot Device2nd Boot Device3rd Boot DeviceBoot Other DeviceSwap Pressing the switch once will have the system enter the sleep/suspend state.
Page 6: Table Of Contents Power Saving Switch Connector: JGS1 ......2-19 Wake On LAN Connector: JWOL1 ........2-19 Wake On Ring Connector: JMDM1 (Optional) ....2-20 IrDA Infrared Module Connectors: IR1 & IR2 Page 5: Table Of Contents Contents Chapter 1. This item applies only when synchronous DRAM isinstalled in the system. Page 99 ® BIOS Setup Chassis Intrusion (Optional) The field enables or disables the feature of recording the chassis intrusion status and issuing a warning message if the chassis is once
When...Page 44: Getting Help AWARD® BIOS Setup Getting Help After entering the Setup utility, the first screen you see is the Main Menu....Page 45: The Main MenuChapter 3 The Main Menu Page 91 ® BIOS Setup Note: If you change these settings, you must reboot the system until it enters the operating system and then power off the system. N8Power Management Setup8PnP/PCI ConfigurationsSave & Exit Setup8PC Health StatusExit Without SavingE Page 71 Chapter 3Set Supervisor/User PasswordWhen you select this function, a message as below will appear on the screen:CMOS Setup If set to Monitor, any activity detected on the specified hardware peripheral or component will wake up the system or prevent the system from entering the power saving modes.
AUX_IN1 connector is for DVD add-on card with Line-in connector. Page 96 Chapter 4Full-Duplex mode permits simultaneous two-direction transmission. Page 103 AMI® BIOS SetupAdditionally, when a password is enabled, you can also have AMIBIOS torequest a password each time the system is booted. Page 14: Chapter 2.
Page 85 AMI® BIOS SetupSetting to Off will allow end users to use the arrow keys on the numerickeypad. Page 104 Chapter 4IDE HDD AUTO DetectionYou can use this utility to AUTOMATICALLY detect the characteristics ofmost hard drives.AMIBIOS SETUP - STANDARD CMOS SETUP(C)1999 American Megatrends, Inc. SCSI The system will boot from the SCSI. Use the arrow keys to highlight the item you want to modify and use the
The Help screen lists the appropriate keys touse.Page 79 AMI® BIOS SetupThe Main MenuOnce you enter AMIBIOS SIMPLE SETUP UTILITY, the Main Menu willappear on the screen. Page 75: Chapter 4.